Flame Cutting Banner.jpg

Torch Boosters supply high pressure gas directly to torches and burners

Refuelers let you fill G-TEC cylinders with high pressure natural gas

Natural Gas Cylinders hold 130 cubic feet of natural gas at 275 psi

Purchase a G-TEC Natural Gas Pressure Booster

How To Install your G-TEC  System

Contact G-TEC if you have questions

High pressure natural gas is the best fuel for flame cutting

The Edison Welding Institute says...

Natural gas is an excellent fuel...it has less tendency to round the top edge of the cut and produced less slag or dross. Also, the dross that was produced...did not adhere as tightly to the plate and was more easily removed. No difference was found in cutting speed between acetylene and natural gas.

Assinck Circle Cut 12-12-01 4x4.jpg

Using a cutting torch fueled by hi-pressure natural gas means cleaner cuts with less slag, less top edge rounding and less time grinding for faster cleanup.

Compared to any other oxy-fuel cutting torch, such as an acetylene torch or a propane torch, natural gas gives top performance at lower cost with similar piercing and cut travel speeds.

Keep the torch body and cutting attachment you already use - simply switch to a natural gas cutting tip!

Cut Piece.jpg
GTEC website banner No Text.jpg

Cut with Acetylene

Cut with Natural Gas

ACETCUT2.jpg
NGCUT2.jpg
DSC06090 Cutting Tips 5x7 100 dpi.jpg

Comparing 1" plate steel cut with acetylene (left) and natural gas (right) shows a cleaner cut with less slag and any slag that is formed is more easily removed from the natural gas cut piece.

TB-500 Closeup.JPG
DSC08521 26 Pierces 2x3 EMAIL.jpg

You only need to change your torch tip to make the switch to hi-pressure natural gas. We have the right tips for all brands and models of cutting torches...hand torches, machine torches and specialty equipment such as powder cutting torches.

Learn more about G-TEC natural gas flame cutting tips.

Hi-pressure natural gas starts fast and pierces quickly.

One New Jersey metal fabricator pierces 1 1/2" plate steel in about 20 seconds with hi-pressure natural gas from a G-TEC TB-500 Torch Booster!

Do you need hi-pressure natural gas for your Messer cutting table with Alfa or Turbo Flame torches?

Cutting Speed.jpg
Messser Alfa Torches.jpg

The newest generation of Messer cutting tables with Alfa and Turbo Flame torches need 25-28 psi natural gas and if your gas utility can't supply this pressure then a G-TEC Torch Booster is the answer.

Get more information about using G-TEC Torch Boosters with Messer Alfa flame cutting torches.

See how well natural gas performs!

Click on the YouTube screen to watch an overview that explains G-TEC Torch Boosters and shows a brief cutting demonstration.

Torch Cutting Brochure.jpg

Pick the right Torch Booster for your shop...

G-TEC Torch Boosters connect to a standard utility gas pipe in your building and boost pressure as high as 45 psi. Just turn the Torch Booster ON at the start of the first shift and OFF at the end of the day - you get an endless supply of high pressure natural gas for you cutting torches. When no torches are lit the Torch Booster automatically puts itself into recirculation  mode - there are no operator controls other and ON and OFF. Torch Boosters deliver gas in exactly the same way as a cylinder or bulk tank except that you save money and never run out of gas!

Dsc08201 Right Side SMALL.jpg

TB-30 Torch Booster - For shops with one oxy-fuel torch TB-30 boosts utility gas pressure to 25 psi with a flow rate of 40 cf/hr. TB-30 measures only 12" wide by 12" tall by 16" deep  - it is quiet and easy to install almost anywhere.

Get more information about TB-30 Torch Boosters.

TB-125 Front Slight Angle With Fan Drop Shadow 8x10 JPEG.jpg

TB-60 Torch Booster - For shops with 2 oxy-fuel torches. TB-60 Torch Booster supply high pressure natural gas at 60 cf/hr at up to 25 psi.

TB-125 Torch Booster - For shops with 3 or 4 torches. TB-125 Torch Booster raises gas pressure as high as 25 psi and delivers 125 cf of gas per hour.

TB-60 and TB-125 Torch Boosters are in cabinets that measure 20" wide, 16" tall and 18" deep, about the size of a window air conditioner.

Get more information about TB-60/TB-125 Torch Boosters

_mg_1264 TB 500 PRINT 4-3 x 3-5.jpg

TB-250 Torch Booster - When you shop has up to 6 torches TB-250 can boost gas pressure as high as 45 psi and delivers 300 cf of gas per hour. Install a regulator to set pressure between 1-45 psi.

TB-500 Torch Booster - When your shop has up to 12 torches TB-500 is our highest capacity Torch Booster and can raise pressure as high as 45 psi at 500 cf/hr. Install a regulator to set pressure between 1-45 psi.

TB-250 and TB-500 Torch Booster measure 28" wide, 24" deep and 20" tall.

Get more information about TB-250 and TB-500 Torch Boosters.

Do you have more than 12 cutting torches or multiple production stations in your shop?

Good news! Torch Boosters can be connected to a gas manifold to supply multiple cutting tables or production areas.

If you have more than 12 torches then 2 or 3 Torch Boosters can be connected together for greater gas flow volume.

Based on your cutting torch requirements G-TEC will design the right combination of Torch Boosters for you.

IMG_8048 5x7 300 dpi.jpg

Torch Boosters supply high pressure gas directly to torches and burners

Refuelers let you fill G-TEC cylinders with high pressure natural gas

Natural Gas Cylinders hold 130 cubic feet of natural gas at 275 psi

Purchase a G-TEC Natural Gas Pressure Booster

How To Install your G-TEC  System

Contact G-TEC if you have questions

GTEC_3DLogo_only.tif