TB-250 Torch Booster

TB-250 and TB-500 Pressure Boosters are high volume, high pressure systems designed

to supply natural gas at up to 45 psi. Both systems can be modified to boost pressure to 70 psi if higher pressure is required for duty cycles of 8 hours per day, or less.


TB-250 and TB-500 Pressure Boosters are easy to use...just turn the system on and

get all the gas you need. There is no internal storage and the system is ready for use as soon as it is turned on.


When you are not using gas the Pressure Booster automatically puts itself into recirculation mode. It is designed to be left running for short periods when gas is not being used and does not require operator attention once it has been started.


TB-250 and TB-500 Torch Boosters elevate gas pressure as high as 45 psi and users can install a regulator to set output pressure between 1 - 45 psi. Flow volumes are 250 scfh for TB-250 and 500 scfh for TB-500. If a natural gas supply rated at 15 psi is available then TB-250 can supply 500 scfh and TB-500 can supply 1,000 scfh.


If you need high pressure natural gas for duty cycles running 24 hours then a Heavy Duty Pressure Booster is a better choice. Click here to see TB-250H and  TB-500H Pressure Boosters.


Both systems measure 28” W x 24” D x 20” T; TB-250 weighs 175 lbs. and TB-500

weighs 285 lbs. In North America electrical requirements are 208V, 60Hz, 30 amp single phase service; in Europe 230V, 50Hz, 30 amp single phase service. Gas supply should be between ¼ to 5 psi and delivered in a 1 1/2” pipe which connected directly to the Pressure Booster.




An important advantage of a TB-250 or TB-500 Pressure Booster is that it can be installed right in the area where high pressure natural gas will be used. Just connect to a low pressure natural gas pipe already in your building and make high pressure natural gas readily available.


Many natural gas compressors must be installed outdoors with lengthy piping required to bring high pressure gas service to the point where it is used. A G-TEC installation is simple and less expensive.


G-TEC systems also do not require special ventilation or other expensive site preparation to be installed in a normal working environment. TB-250 and TB-500 Pressure Boosters are quiet and will fit right into your workspace.

Certified by CSA International, an OSHA Nationally Recognized Testing Laboratory

TB-250/TB-500 Pressure Boosters are Certified By CSA-International

CSA International is accredited in the United States by the Occupational Safety and Health Administration (OSHA) as a Nationally Recognized Testing Laboratory (NRTL), and in Canada by the Standards Council of Canada (SCC).


Across North America the CSA label on the G-TEC Pressure Booster is sufficient for approval by building inspectors, fire marshals and other authorities.


G-TEC Pressure Boosters are even welcomed in buildings that prohibit fuel gases such as propane which are stored in cylinders or bulk tanks.


CE Compliant for use in

European Union countries

G-TEC Pressure Boosters are compliant with Council Directives for electrical equipment,electromagnetic compatibility, machinery and  pressure equipment.


Click here to download the CE Declaration of Conformity

CE Statement of Conformity G-TEC Systems are CE Compliant

A G-TEC Pressure Booster can be 50% less expensive to purchase and install compared to other high pressure natural gas compressors because the equipment itself costs less and installation is not as complex as an outdoor compressor requires.

There is no expensive administrative time to secure permits, no special safety or environmental site requirements. Maintenance is simple to perform and parts are not expensive. Training required for operation and maintenance is minimal.

G-TEC Pressure Boosters connect to a low pressure natural gas pipe that is already in your building and boost pressure to 45 psi.


The system has 2 gas inlets, one if your building supply pressure is less than 1 psi and a second for utility natural gas pressure between 1-5 psi.


On the high pressure outlet many G-TEC users will install a regulator to set pressure between 1-45 psi or the system can be connected to a downstream process at the full output pressure of 45 psi.





There are separate gas inlets for supply of natural gas at <1 psi or between 1-5 psi

G-TEC Pressure Boosters do not require expensive site preparation

High Capacity Torch Boosters

Find out more about how G-TEC TB-250 and TB-500 Pressure Boosters can support your high pressure natural gas requirements. Contact Ed Howard at 1-800-451-8294 in North American or CC+1-716-831-9695 internationally.


Or click this link to send an e-mail.


Limited Pressure Booster customization is available for supply gas pressure, output pressure and flow volume. Contact G-TEC with your specific requirements and let us help select the right system for your work.

TB-15/TB-30 Torch Boosters

TB-15 / TB-30

Pressure Boosters

for pressure up to 25 psi and flow up to 30 scfh

High Capacity Pressure Boosters

for for pressure up to 150 psi and flow up to 500 scfh.


Return to the home page

TB-60/TB-125 Torch Boosters

TB-60 / TB-125

Pressure Boosters

for pressure up to      25 psi and flow up to 125 scfh

Simple indoor installation without special site preparation