Refueler 60 makes it simple to take high-
across town. Just connect Refueler 60 to an Adsorbed Natural Gas Cylinder and press
the START button to begin the filling process.
Once started filling cylinders is automatic. Cylinders are pressurized to 275 psi and the
Refueler 60 turns itself off without operator attention. Many G-
their cylinders overnight and start each morning with full natural gas supplies.
Refueler 60 can fill a single cylinder or as many as four at once with a G-
Cylinders attached for filling do not need to be completely empty, each cylinder can be
at a different level of fullness -
Cylinders fill at a rate of one cubic foot per hour.
Refueler 60 is compact, just 20” wide, 18” deep and 16” tall -
Electrical requirement is 120V 20 amp and there is a 230V 50Hz configuration available, as well.
It is quiet, does not require any special site preparation and can be installed “anywhere” that is
consistent with local codes and regulations for cylinder filling. The system includes a flexible
5’ hose for connection to the gas pipe and a shutoff valve. Refueler 60 should be located in an
area where temperatures range between 40F to 85F/22C to 29C.
CSA International Certifies Refueler 60 for performance, reliability and safety. In the United States
it can be operated by anyone who has received proper safety training but does not require a
special license or certificate. Requirements to operate Refueler 60 may be different in other countries.
Refueler 60 is CE Compliant for use in European Union countries, as well.
G-
Once started the filling process is automatic and Refuelers turn themselves off when cylinders are full.
Refueler 180 is a high volume cylinder filling systems that makes it simple to take
high-
connect Refueler 180 to an Adsorbed Natural Gas Cylinder and press the START
button to begin the filling process.
Once started filling cylinders is automatic. Cylinders are pressurized to 275 psi and
the Refueler 180 turns itself off without operator attention. Many G-
Start the filling process at the end of the day, refill their cylinders overnight and
begin each morning with full natural gas supplies.
Refueler 180 is designed for high-
in use on the shop floor or mounted on fleet trucks. A G-
four empty cylinders to a single Refueler 180 and manifolds can be daisy-
to fill More cylinders at one time.
Cylinders do not need to be completely empty, each cylinder can be at a different
level of fullness -
Cylinders fill at a rate of three cubic fet per hour.
Refueler 180 is compact, just 28” wide, 24” deep and 20” tall -
Electrical requirement is 120V 20 amp and there is a 230V 50Hz configuration available, as well.
It is quiet, does not require any special site preparation and can be installed “anywhere” that is
consistent with local codes and regulations for cylinder filling. Refueler 180 should be located in an
area where temperatures range between 40F to 85F/22C to 29C.
CSA International Certifies Refueler 60 for performance, reliability and safety. In the United States
it can be operated by anyone who has received proper safety training but does not require a
special license or certificate. Requirements to operate Refueler 180 may be different in other countries.
Refueler 180 is CE Compliant for use in European Union countries, as well.
G-
to a single Refueler 60 or Refueler 180 Cylinder Filling System.
Cylinders of different sizes and different levels of fullness can be connected
at the same time and all will be filled together and be finished at the same time.
G-
back flow from the cylinder.
G-
without having to disconnect them. Continuous Operation Manifolds are most often
used for torch applications where gas flow is usually below 60 cf/hr (Refueler 60) or
below 180 cf/hr (Refueler 180) but higher gas flows are required periodically that would
exceed system capacity.
G-
and allow it to be used as a reserve for situations where high volume gas flow is required for
brief periods of time.
DM-
Directly to torches, shop manifolds and automated torch equipment.
DM-
Torch Booster in a single cabinet. When filling cylinders DM-
per minute and can fill from one to four cylinders simultaneously. As a Torch Booster
DM-
A built-
DM-
Electrical requirement is 120V 20 amp and there is a 230V 50Hz configuration available,
as well. It is quiet, does not require any special site preparation and can be installed
“anywhere” that is consistent with local codes and regulations for cylinder filling.
The system includes a flexible 5’ hose for connection to the gas pipe and a shutoff valve.
DM-
40F to 85F/22C to 29C.
CSA International Certifies DM-
States it can be operated by anyone who has received proper safety training but does
not require a special license or certificate. Requirements to operate DM-
different in other countries.
Refueler 60 is CE Compliant for use in European Union countries, as well.
check valve scheduled maintenance instructions
Natural gas cylinder
sold separately.
Above -
Below-
