HeavyDuty

When Torch Boosters are used in an environment where ambient temperature is consistently above 90F / 32C, where the duty cycle is more than 16 hours per day or where the application requires outlet pressure greater than 60 psi, a Heavy Duty Torch Booster is recommended. Heavy Duty Torch Boosters add a Cooler Module that keeps the compressor temperature low, extends system life span and eliminates the 3 hour cool down cycle that is common with Standard Duty units.


Learn more about G-TEC Heavy Duty Torch Boosters:


TB-HVOF - pressure up to 150 psi  for High Velocity Oxy-Fuel thermal spray


TB - 500C - pressure up to 60 psi, flow rate up to 500 scfh


TB-250C - pressure up to 60 psi, flow rate up to 250 scfh


TB-250H - pressure up to 150 psi, flow rate up to 250 scfh


TB-125C - pressure up to 25 psi, flow rate up to 150 scfh

Download a TB-250H

Brochure

Return To The Torch Booster Page / Return To The Top Of This Page / Return To The Home Page

Refuelers let you fill

G-TEC cylinders with high

pressure natural gas

Order a G-TEC

Natural Gas

Pressure Booster

How To Install your

G-TEC System

G-TEC Systems are

Approved across the

US and Canada

Contact G-TEC

if you have questions

Torch Applications

work better with high

pressure natural gas

Natural Gas Cylinders

hold high volumes of

natural gas at only 275 psi

Download a TB-125C

Brochure

Refuelers let you fill

G-TEC cylinders with high

pressure natural gas

Order a G-TEC

Natural Gas

Pressure Booster

How To Install your

G-TEC System

G-TEC Systems are

Approved across the

US and Canada

Contact G-TEC

if you have questions

Torch Applications

work better with high

pressure natural gas

Natural Gas Cylinders

hold high volumes of

natural gas at only 275 psi

TB-500C Torch Boosters modify Standard Duty TB-500 Torch Boosters to add a Cooler Module.


TB-500C Torch Boosters are suitable for pressures up to 60 psi. This Torch Booster uses 2 sets of flexible hoses that connect the Booster to the Cooler. Pumps in the Cooler Module cycle compressor oil into the Cooler, remove excess heat then return the oil to the Torch Booster. Electrical power is slaved from the Torch Booster and the Cooler Module starts when the Torch Booster starts. Both cabinets measure 28” wide, 24” deep and 20” tall. The Cooler Module weighs 157 pounds and can be stacked on top of the Torch Booster to minimize footprint space.


Electric service is 208V single phase 30 amp 60 Hz in North America or 230V single phase 30 amp 50 Hz worldwide. Low pressure supply pipe must be at least 1 1/2” diameter.

Download a TB-250C/

TB-500C Brochure

TB 250H Brochure.pdf

TB-250C and H Torch Boosters modify Standard Duty TB-250 Torch Boosters to add a Cooler Module.


TB-250C Torch Boosters are suitable for pressures up to 60 psi; TB-250H Torch Boosters are suitable for applications between 60-150 psi. Flow rate is 300 cubic feet per hour.


These Torch Boosters use a set of flexible hoses that connect the Booster to the Cooler. A pump in the Cooler Module cycles oil between the Booster and the Cooler to remove excess heat from the Booster. Electrical power is slaved from the Torch Booster and the Cooler Module starts when the Torch Booster starts. The Booster cabinets measure 28” wide, 24” deep and 20” tall. The Cooler Module is 20” wide, 18” deep and 16” tall, weighs 107 pounds and can be stacked on top of the Torch Booster to minimize footprint space. Electric service is 208V single phase 30 amp 60 Hz in North America or 230V single phase 30 amp 50 Hz worldwide. Low pressure supply pipe must be at least 1 1/2” diameter.

Heavy Duty Torch Boosters for challenging operating environments

TB-125C Torch Boosters modify Standard Duty TB-125 Torch Boosters to add a Cooler Module. Outlet pressure is up to 25 psi with a flow rate of 150 cubic feet per hour.


TB-125C Torch Booster uses two cabinets, each measuring 20” wide, 18” deep and 16” tall. The Cooler Module weighs 105 lb and can be stacked on top of the Torch Booster module. Power requirement is 120V 20 amp. Low pressure supply pipe should be minimum 1” diameter.


A single set of control buttons, power/start/stop, on the Booster Module (right) also operate the Cooler Module (left). Once started no operator attention is required - the Booster will automatically adjust to flow demand of the application.

The Cooler Module (left) connects to the Booster Module (right) with flexible hoses. Hot oil from the Booster is cooled by flowing through radiators in the Cooler and returns to the compressors.

A single set of control buttons, power/start/stop, on the Booster Module (right) also operate the Cooler Module (left). Once started no operator attention is required - the Booster will automatically adjust to flow demand of the application.

The Cooler Module (left) connects to the Booster Module (right) with flexible hoses. Hot oil from the Booster is cooled by flowing through a radiator in the Cooler and returns to the compressor.

A single set of control buttons, power/start/stop, on the Booster Module (right) also operate the Cooler Module (left). Once started no operator attention is required - the Booster will automatically adjust to flow demand of the application. Hot oil from the Booster is cooled by flowing through a radiator in the Cooler and returns to the compressor.

TB-HVOF is a Heavy Duty Torch Booster designed for High Velocity Oxy-Fuel Thermal Spray applications where gas pressure up to 150 psi is required and gas flow volume is up to 500 scfh.

The Booster and Cooler functions are combined in a single cabinet that measures 50 1/2” wide, 33” deep and 32” tall.

Supply gas pressure should be between ¼ to 5 psi but if 15 psi supply gas is available TB-HVOF can operate 2 HVOF spray guns simultaneously. Supply pipe must be at least 1 1/2” diameter.

Power requirement is 208V single phase 60 Hz 30 amp or 230V single phase 50 Hz 30 amp service.

Weight is 550 pounds / 249 kg.

TB-HVOF is also suitable for other applications requiring gas pressure greater than 60 psi up to 150 psi.

TB-HVOF Brochure PDF.pdf

Download a TB-HVOF Brochure